Lexan housing and lens sonic welded for a permanent seal. Legal in either vertical or horizontal mounting position for U.S. and ECE applications. Includes No.421R light, No.421-18 grommet and No.421-491 right angle, 3-wire plug with an added terminal for double filament bulb Interchangeable with all competitive units. 6-1/2 in W x 2-1/4 in H.

Durable, black ABS housing with snap-on red acrylic lens.

Solid state construction, no bulbs to break or burn out. 100,000 hrs rated life. Fully sealed, submersible construction. Potted circuitry(coated and sealed) protects against moisture, corrosion and vibration. Lower amp draw than incandescent lights. Designed to directly replace 440-Series incandescent lights. Integral, dedicated side marker diode. Exceeds all DOT rear lighting and reflex requirements for trailers less than 80 in wide. 4-1/2 in W x 4-1/2 in H x 2 in D.

Wrap-over lens retained by 2 screws. Black, plastic dust-resistant housing. Supplied with 10 in lead wires. Universal stud mount with 1/4 in studs on 2 in centers. 3-3/4 in H x 2-5/8 in D overall.

Acrylic lens snaps onto housing. Two bulb lamp functions as clearance or side marker light and may be used as combination clearance and side marker when properly mounted on 3 in centers and grounded through mounting hardware. Single wire for electrical connection. 15,000 hrs long life bulbs. 4 in W x 2 in H x 1-1/8 in D.

Low-profile lamp functions as tractor or utility light with bright 55 W, H3 replaceable bulb. Features high-impact polycarbonate housing and adjustable stainless steel mounting hardware.

Kit with decorative snap-on chrome bezel included. Hard-wired design eliminates the need for separate plug and reduces connection points. Designed for horizontal installation. 9 to 16 V operating range. Meets FMVSS 108 requirements.

Stud mount side marker or clearance light with built-in reflector optics to eliminate the need for a separate reflector. Push stripped power wire into "Quick-Lock" port to connect. Single wire for electrical connection. Features 15,000 hr long life bulb.

Sturdy plastic housing with a black finish. Brass socket and lexide lens gasket for long life. 5-1/2 in face Dia, 4-1/2 in Dia inset and 1-1/2 in D overall.

Sealed 2-diode LED light alternative to traditional incandescent 154-Series lights. Operates from 9 to 16 V. Features 2-wire, hard-wired design. Ground wire includes #10 ring terminal. Mounts on 3 in centers. Mounting gasket included. One-piece housing sealed with epoxy eliminates weld joints. 4-1/16 in L x 1-1/16 in W x 15/16 in D.

PM Stop, Stud Mounting, Plastic Housing Material, Black Housing, 2-5/8 in Width, 3-3/4 in Height, Includes: (3) Stop, Turn and Tail Lights

Includes the following functions: stop, turn, tail, rear clearance, rear reflex, side marker and side reflex. Features gaskets on both rear and side lenses. Grounds through mounting studs. Mounts on 2 in centers and includes mounting hardware.

Submersible rear lighting kit and reflectors for all trailers 80 in wide and over. Includes 856/856L LED taillights plus license bracket, mounting hardware and installation instructions. 7-15/16 in W x 2-7/8 in H x 2-7/8 in D.

Solid state construction, no bulbs to break or burn out. 100,000 hrs rated life. Fully sealed, submersible construction. Potted circuitry(coated and sealed) protects against moisture, corrosion and vibration. Lower amp draw than incandescent lights. Designed to directly replace 440-Series incandescent lights. Integral, dedicated side marker diode. Exceeds all DOT rear lighting and reflex requirements for trailers less than 80 in wide. 4-1/2 in W x 4-1/2 in H x 2 in D.

Tough molded acrylic lens. Used to replace lenses of Peterson No 440, 441, 444 and 452 series lights. 4-1/2 in square.

Mounts with two stainless steel screws on 2 in centers and has separate ground wire for non-metallic surfaces. Polished, chrome-plated brass housing with hooded shield to prevent upward glare. 2-9/16 in W x 1-3/16 in H x 1 in D.

Sealed 2-diode LED light alternative to traditional incandescent 154-Series lights. Operates from 9 to 16 V. Features 2-wire, hard-wired design. Ground wire includes #10 ring terminal. Mounts on 3 in centers. Mounting gasket included. One-piece housing sealed with epoxy eliminates weld joints. 4-1/16 in L x 1-1/16 in W x 15/16 in D.

Acrylic lens features built-in reflector and precision OE style, prism optics for a brilliant signal and to eliminate the need for a separate reflector. Includes a durable molded base with single bulb socket and single lead wire; grounds through mounting screw. 4-1/8 in W x 2 in H x 1-1/32 in D, mounts on 3 in centers.

Features three 1/4 in mounting studs on 2 in triangular pattern. Includes stop, turn, tail, back-up and license light functions. Will fit Peterbilt, Mack, White and Jeep. 6-1/4 in W x 6-3/4 in H x 2-3/4 in D overall.

Use on parking light, directional light and side marker light. 1-7/8 in x 5 ft, on a card.

Use on parking light, directional light and side marker light. 1-7/8 in x 5 ft, on a card.

Solid state construction, no bulbs to break or burn out. 100,000 hrs rated life. Fully sealed, submersible construction. Potted circuitry(coated and sealed) protects against moisture, corrosion and vibration. Lower amp draw than incandescent lights. Designed to directly replace 456-Series incandescent lights. Integral, dedicated side marker diode. Exceeds all DOT rear lighting and reflex requirements for trailers 80 in wide and over. 7-15/16 in W x 2-7/8 in H x 2-7/8 in D.

Chrome-plated steel housing and mounting bracket in traditional styling for numerous applications. 1-7/8 in projection, 2-3/4 in W x 2 in H bracket mounts on 2 in centers.

Functions as clearance, side marker or identification light and may be used as combination side marker and clearance light when properly mounted. Durable base with external mounting holes. Lens snap-locks onto base. Includes single lead wire and grounds through mounting screw. 3-1/4 in W x 1 in x 1-1/8 in D, mounts on 2-3/4 in centers.

For courtesy, interior or instrument lights, commonly used to illuminate license plate or step bumpers. Chrome-plated steel housing snaps into 1-1/4 in Dia holes. 1-1/2 in Dia overall. 2 required for legal license illumination.

Corrosion-resistant, zinc-plated, painted with white baked enamel. Three 3-1/4 in x 1 in x 1-1/8 in #107 compact lights attached to each bar. Lights have acrylic lenses that lock into base to protect against being knocked out. Mounts on 16-1/2 in centers and grounds through mounting hardware. 16-1/8 in W x 1 in H x 1-3/8 in D, 16-1/2 in L with mounting brackets.

Acrylic lens snap-seals onto housing. Single wire connection, grounds through mounting hardware. 15,000 hrs long-life bulb. When properly mounted, may be used as combination side marker and clearance light. 4-1/8 in W x 2 in H x 1-1/32 in D, mounts on 3 in centers.

Under 80 in wide combination taillight. Includes the following functions - stop, turn, tail, rear reflex, side marker and side reflex. Includes lead wire. Grounds through 1/4 in mounting studs. Studs on 2 in centers.

Durable, black ABS housing with two snap-on amber lenses.

Tough molded housing and lenses with phosphor bronze contacts for durability. Belljar design, gasketed lenses prevent water from reaching bulbs and contacts. Use as a rear light for over 80 in wide applications. Exceeds DOT requirements for stop, turn, tail, rear and side reflector, side marker and rear clearance. Includes No.452 Belljar submersible lights, 25 ft trailer harness, 48 in trunk connector, plastic license bracket, all mounting hardware and installation instructions. Front side marker lights and reflectors needed to meet DOT requirements.